Elgato capture recording corrupted or won't play? Recovery and prevention
By the FixMP4 engineering team · · 9 min read
With an Elgato capture card, the card captures the signal from your console, camera or second PC, and software on your computer encodes and writes the file. That software might be Elgato's own 4K Capture Utility, the older Game Capture software, or a third-party app such as OBS. When a recording turns out broken, the cause is almost always on the computer side: the software stopped before finishing the file, the connection to the card dropped, or the file uses a format your player cannot handle. Here is how to tell which, and how to get the footage back.
Is it damage or a codec issue?
Start by opening the recording in VLC.
- VLC plays it fine but Windows or your editor does not: the file is healthy and the issue is decoding. Elgato software can record in HEVC (H.265), which many apps do not decode without extra support. See the HEVC section below.
- VLC fails, shows 0:00, or plays only a few seconds of a long session: the file is damaged, usually because it was not closed properly.
Check the file size too. A two-hour session at a high bitrate should be many gigabytes. A large file that does not play is a strong sign that the data is there but the index is missing.
When the recording was interrupted
MP4 files store the frames as they are captured, and the software adds an index when you press stop. These events prevent that final step:
- the PC crashed, froze or restarted for updates during capture;
- the capture software crashed or was force-closed;
- the USB connection to an external card dropped, for example because of a loose cable, a hub or a power-saving setting;
- the recording drive filled up;
- the laptop battery ran out.
In each case, the file on disk is a long run of video and audio data with no table telling players where anything is.
Rebuilding the index
- Copy the broken file to a safe location and work on the copy.
- Record a short reference. Use the same Elgato card, the same software and identical settings: resolution, frame rate, encoder (H.264 or HEVC), bitrate mode and audio. Ten to twenty seconds of anything is enough.
- Open the FixMP4 repair tool and add the broken recording plus the reference.
- FixMP4 reads the raw frames and writes a new index, entirely in your browser. Large captures stay on your machine.
- Check the free preview to confirm the content, then save the repaired file.
FixMP4 supports H.264 and HEVC with AAC audio. If you captured with a format outside that list, the repair may not be possible. For detail on picking the right reference, see how to choose a reference file.
Elgato's flashback and timeshift recordings
Elgato's capture software has offered ways to record continuously in the background and save a section afterwards, sometimes called flashback recording. Those modes keep a temporary buffer. If the software or PC crashed before you saved the section, the buffer may not have been turned into a normal file. Look in the software's settings for its temporary or cache folder; if a large recent file exists there, copy it and treat it as an interrupted recording. If nothing is there, the buffer was not kept.
HEVC playback and editing
Capturing in HEVC halves file sizes compared with H.264 at similar quality, which is attractive for 4K and HDR. The cost is compatibility:
- Windows apps need the HEVC Video Extensions from the Microsoft Store.
- Editors vary in their HEVC support, and HDR HEVC adds its own requirements.
- Older computers may decode HEVC slowly, causing stutter that looks like damage but is not.
If HEVC causes trouble, either record in H.264 or convert the finished file. The guide to repairing and playing HEVC video covers the details, and HEVC vs H.264 for recording explains the trade-offs.
Using Elgato cards with OBS
Many people capture with OBS instead of Elgato's software, adding the card as a video capture device. In that case, OBS writes the file and its recording format setting decides how a crash ends. Recording to MKV and remuxing afterwards protects long sessions. For OBS files that broke, follow recovering a corrupted OBS recording.
Preventing broken captures
- Use a direct USB port on the computer, not a hub, and a good-quality cable. Disable USB selective suspend in Windows power settings for desktop capture rigs.
- Install updates for the capture software and card firmware between sessions, not during them. Postpone Windows restarts during long recordings.
- Record to a fast internal drive with plenty of space, not an almost-full system drive.
- Monitor the session for dropped frames or warnings. A capture that starts dropping frames is often about to fail.
- For long events, split recording into segments if your software supports it, so a crash costs one segment rather than the whole event.
General habits for every device are listed in how to prevent corrupted recordings.
Summary
If your Elgato recording plays in VLC, the problem is HEVC support, not damage. If it does not play anywhere and has a realistic size, the software was interrupted before writing the index. Rebuild it in FixMP4 with a short reference capture made with the same card and settings, and use stable connections and crash-tolerant settings for future sessions.
Frequently asked questions
Why won't my Elgato recording open?
If the capture software, the PC or the capture card connection stopped while recording, the MP4 may have been left without its index, and players cannot open it. It can also be a healthy HEVC file that your player cannot decode, which looks similar at first.
My Elgato recording is HEVC. Why won't it play in Windows?
Windows needs the HEVC Video Extensions from the Microsoft Store to play H.265 in the built-in apps, and some editors need extra support too. VLC plays HEVC without additional installs, so it is a good first test.
Can I recover an Elgato recording after the PC crashed?
Often, yes. If the file has a large size but will not play, FixMP4 can rebuild its index in your browser. Make a short reference recording with the same Elgato software, card and settings first.
Does the capture card itself corrupt recordings?
The card passes the video signal to the computer; the file is written by the software on the PC. Unstable USB connections, cables or power can interrupt capture and leave a damaged file, so the connection matters even though the card does not write the file.
Have a broken recording right now?
Diagnose it and hear or watch a free repaired preview. Nothing is uploaded.
Open the repair tool